80NG/80NGS

Natural gas Generator Set

Main configuration and features:

•  Highly efficient gas engine. & AC synchronous alternator.

•  Gas safety train and gas protection device against leakage.

•  Cooling system suitable for ambient temperature up to 50℃.

•  Strict shop test for all gensets.

•  Industrial silencer with silencing ability of 12-20dB(A).

•  Advanced engine control system: ECI control system including: ignition system, detonation control system ,speed control system , protection system，air/fuel ratio control system and cylinder temp.  

•  With cooler and Temperature Control System to make sure the unit can work normally at 50℃ environment temperature. 

•  Independent electrical control cabinet for remote control.

•  Multi-functional control system with simple operation.

•  Data communication interfaces integrated into control system.

•  Monitoring battery voltage and charging automatically.

Special statement：

1、   The technical data are based on natural gas with a calorific value of 10 kWh/Nm³ and a methane no. > 90%

2、   The technical data indicated is based on standard conditions according to ISO8528/1, ISO3046/1 and BS5514/1

3、   The technical data is measured in standard conditions: Absolute atmospheric pressure：100kPa

      Ambient temperature：25°C Relative air humidity：30%

4、   Rating adaptation at ambient conditions according to DIN ISO 3046/1.The tolerance for the specific fuel consumption is + 5 % at rated output.

5、   Dimension and weight above are just for standard  product and may be subject to change. As this document is used only for presale reference, take                           the specification supplied by Smart Action before ordering as final.

6、   The applicable ambient temperature is -30 ° C ~ 50 ° C; when the ambient temperature exceeds 40 ° C, the rated power is reduced by 3% for every     

5 ° C increase in temperature. Applicable altitude is less than 3000 meters; when the altitude exceeds 500 meters, the rated power is reduced by 5% for  every 500 meters of height.

[1] Emission values downstream of catalytic converter based on dry exhaust.

Gas Data
Fuel		[1]                                                         Natural gas
Gas intake pressure		5Kpa~50Kpa
Methane volume content		≥ 80%
Low heat value（LHV）		Hu ≥ 31.4MJ/Nm3
Gas Consumption per hour at 50% load                                              at 75% load                                              at 100% load		13.5 m3  19.5 m3 25 m3
[1] After the Natural gas components need to be provided by users, the relevant data of the technical manual will be revised.Gas hoses are ECER110 approved. Components in the gas train meet Directive 90/356/EWG.
Service
Oil level (ambient temperature is higher than minus 5°C/ ambient temperature is[2] lower than minus 5°C)	API 15W-40 CF4 /API 10W-30 CF4
Lubricating oil capacity min./max.	17 L / 18 L
Coolant capacity	40 L
Coolant type	50% softened water and 50% anti-freezing solution (ethylene glycol, with the concentration of the anti-freezing solution between 40%-68% )
installation room ventilation  (inlet air volume flow )	＞8500 m³/h

[2] The oil standard refers to factors such as local ambient temperature and air pressure.

Alternator compliance withGB755, BS5000, VDE0530, NEMAMG1-22, IED34-1, CSA22.2 and AS1359 standard. 

In case of nominal mains voltage variations by ± 2%, an automatic voltage regulator (AVR) must be used.

SAC-200 Control system

Programmable control system is adopted with touch screen display , and various functions, including: engine protection and control, paralleling between gensets or gensets and grid, as well as communication functions. etc.  

Main advantages

→ Premium gen-set controller for both single and multiple gensets operating in standby or parallel modes.

→ Support of complex applications for power production in data centres, hospitals, banks and also CHP applications.

→ Support of engines both with electronic unit – ECU and mechanical engines.

→ Complete control of the engine, alternator and controlled technology from one unit provides access to all measured data in a coherent and time corresponding way.

→ Wide range of communication interfaces allows smooth integration into local monitoring systems (BMS, etc.)

→ Internal built-in PLC interpreter allows you to configure customised logic to meet demanding customer requirements on your own without extra programming knowledge and in a fast way.

→ Convenient remote control and service  

→ Enhanced stability and safety

Dimensions are for reference only.